Monthly Archives: August 2013

How To Lengthen Working Life of HSS Circular Saw Blades

Posted on by

In order to reduce the consumption of HSS circular saw blade at maximum limit and meanwhile reduce the cutting and sawing cost for every time working, you’d better follow these tips to improve HSS circular saw blades working life.

Firstly, take a try using on the new saw blade. In general, in order to have longer working life, the circular sawing machine and new saw blade should have enough running-in process, at the beginning ten minutes for sawing and cutting, it is necessary to reduce the cut material feeding speed, and then you should gradually speed up.
Continue reading »

Four Tips About Using Circular Saw Blade Correctly

Posted on by

When being asked about how to use TCT circular saw blade correctly, can you give the right answer? This is the exact article for you.

Firstly, the tool bit and cutting edge of TCT circular saw blade is so sharp, therefore when moving, installing and dismantling saw blade, the workers should be more careful so as to avoid being damaged with such sharp saw blade.
Continue reading »

Four Main Reasons for Saw Blade Abrasion

Posted on by

Saw blade would be abraded and even damaged with these reasons introduced below.

Firstly, improper operating ways or wrong maintenance ways in daily life. The feeding speed for every cutting and sawing equipment should be different, therefore the TCT saw blade should be designed with right angles according to the different cut materials. If the match is not right, its using effect would be reduced.
Continue reading »

Using Circular Saw Blade With These Right Ways

Posted on by

Do you know how to use circular saw blades correctly? This is the right topic I will discuss in the following article.

Firstly, after the saw blade is installed stably and firmly, you should idle it for about 30 seconds to check whether everything is OK. If yes, it is time for you to begin cutting and sawing work.
Continue reading »

Two Common Problems When Using Circular Saw Blade

Posted on by

When using TCT circular saw blade for cutting and sawing some materials such as wood, you would face some problems, do you know the reasons and how to deal with such condition?

Here are two common problems about TCT circular saw blade using and you can follow the solution introduced to solve.

Firstly, the saw blade is so blunt that it is difficult to cut and saw.

Possible reasons for such problem.
Continue reading »

Two Basic Knowledge About TCT Circular Saw Blade

Posted on by

This is one article about TCT circular saw blade and some basic knowledge on this topic would be learned after reading this article, I am sure.

What’s TCT circular saw blade?
When being asked such question, can you give the right definition? TCT circular saw blade is also known as TCT saw blade. In short, it is the round saw blade, after being processed with specific production processes and heat treatment, there are too many sawteeth on the round and thin steel plate, meanwhile, hard character metal cutting head is inlaid at the toothed wheel parts.
Continue reading »

How To Install Saw Blade Correctly

Posted on by

Only with the right saw blade installation, saw blade using safety can be guaranteed during the working process. Follow these steps to ensure correct installation.

Firstly, the rotation direction of saw blade should be the same as the machine principal axis’s direction. If such direction is opposite, it is likely to lead to saw blade dropping, flying saw blade pieces and other dangerous accident.

Secondly, how to choose ring flange? In general, its inner diameter should be the same as saw blade while its external diameter should be about that of 1/3 saw blade. Meanwhile, please ensure such ring flange is not worn down unusually and curved. On its surface, it should be clean without any items even pieces.
Continue reading »

Follow These Two Tips To Ensure Circular Saw Blade Using Safety

Posted on by

When using circular saw blade for sawing and cutting, worker should be more careful because saw blade is so sharp and dangerous. Without right operating way, it is easy to result in physical injury. Here are some tips you can follow in order to ensure right operating.

Firstly, check the working environment

All the machines should be installed with protective cover, otherwise the damaged saw blade or saw blade fragments would fly aimlessly to lead to hurt.
Continue reading »

Five Reasons for Circular Saw Blade Abrasion

Posted on by

During the circular saw blade using process, you would notice that it would be worn down gradually, at this time, have you considered such question that which factors will accelerate such damage? In the article below, I will discuss the topic of saw blade abrasion.

Firstly, mechanical abrasion. When cutting and sawing process, the cut material will lead to different degrees scratching on saw blade surface because of rub. In general, the lower hardness proportion between cut material and saw blade, the easier abrasion of saw blade. Therefore if you want to avoid such abrasion, you have to improve the hardness of saw blade so as to improve its wear resistance.
Continue reading »

How To Improve Circular Saw Blade Working Life

Posted on by

Circular saw blade will be abraded slowly during the cutting and sawing process, which is inevitable. However, you can still use other ways to improve the circular saw blade’s working life. Here are some related tips you can take a try.

Firstly, raw material for saw blade. It is better to choose the raw material with good performance of heat resistance for saw blade production. At the same time, they would have higher toughness, good strength, small stress and deformation. Every tooth holder’s depth and angle should be the same, common difference would be more accurate. In short, raw material’s density, thickness and even hardness should be the same.
Continue reading »